Dual servo aileron...
#1
Senior Member
Thread Starter
My Feedback: (2)
Join Date: May 2002
Location: Stanhope, NJ
Posts: 362
Likes: 0
Received 0 Likes
on
0 Posts
Dual servo aileron...
Hello All,
I am going to be building (I hope...) a plane that will use 2 servos per single aileron. This will be my first at this method. How do I know if the servos are fighting each other (wasting precious mA's) and can I split the aileron in 2 and have each servo drive 1/2 of one aileron? That way, they will operate together in all respects but will not fight each other... Good idea? I think I seen the idea on this forum... As always, thank you.
Justrfb
I am going to be building (I hope...) a plane that will use 2 servos per single aileron. This will be my first at this method. How do I know if the servos are fighting each other (wasting precious mA's) and can I split the aileron in 2 and have each servo drive 1/2 of one aileron? That way, they will operate together in all respects but will not fight each other... Good idea? I think I seen the idea on this forum... As always, thank you.
Justrfb
#3
Senior Member
Dual servo aileron...
All aspects considered, your solution to make each aileron into two is the most fail safe solution. You will not have to worry about one servo fighting the other or have programming problems; plus, should one fail you still maintain a good degree of control with the remaining one. You have a good KISS (keep it simple stupid) solution.
#4
Senior Member
My Feedback: (1)
Join Date: Sep 2002
Location: Leland,
MS
Posts: 405
Likes: 0
Received 0 Likes
on
0 Posts
Dual servo aileron...
Why not use a bellcrank setup to make one servo push(and pull) the aileron from two different points. I've been tinkering with this idea for a while. You'd never have the fighting problem and it would save you some weight also. You'd just have to use a higher torque servo if you're looking for torque.
#5
Senior Member
Join Date: Jun 2002
Location: Baltimore, MD
Posts: 856
Likes: 0
Received 0 Likes
on
0 Posts
Dual servo aileron...
justrfb
If you are using the hitec 5945 or 5645 you don't need two aileron servos, one will work just fine. Are you still considering the 1/3 scale GP Extra?
You can tell if digitals are fighting each other because they will make a whining sound, you'll be able to hear if they are fighting each other.
If you are using the hitec 5945 or 5645 you don't need two aileron servos, one will work just fine. Are you still considering the 1/3 scale GP Extra?
You can tell if digitals are fighting each other because they will make a whining sound, you'll be able to hear if they are fighting each other.
#6
Senior Member
My Feedback: (4)
Dual servo aileron...
The split aileron is a good (if unconventional) idea. Another way to go is the cheapskate method (Which this cheapskate used on HIS GP Extra 330L).
Hook the servo with the shortest arm straight to the aileron, Then put a small bend in the longer pushrod. If the two servos have any deviation between them, it won't be much, and the slight bend will accomodate for it if there is any. I wouldn't recommend this if you're going to put a Volkswagon engine in the thing and do any 3-D stuff, but for simple aerobatics, mine held up fine with standard servos.
Hook the servo with the shortest arm straight to the aileron, Then put a small bend in the longer pushrod. If the two servos have any deviation between them, it won't be much, and the slight bend will accomodate for it if there is any. I wouldn't recommend this if you're going to put a Volkswagon engine in the thing and do any 3-D stuff, but for simple aerobatics, mine held up fine with standard servos.
#7
Senior Member
Join Date: Aug 2002
Location: Bloomington, MN,
Posts: 762
Likes: 0
Received 0 Likes
on
0 Posts
Dual servo aileron...
justrfb,
I like the split aileron idea best, if you really can't get the torque you need from one servo. It would be hard to guarantee that two servos rigidly connected to the same control surface wouldn't fight each other.
banktoturn
I like the split aileron idea best, if you really can't get the torque you need from one servo. It would be hard to guarantee that two servos rigidly connected to the same control surface wouldn't fight each other.
banktoturn
#8
Senior Member
Thread Starter
My Feedback: (2)
Join Date: May 2002
Location: Stanhope, NJ
Posts: 362
Likes: 0
Received 0 Likes
on
0 Posts
Yes I am...
Thanks Giant Scale, MikeB and banktoturn for your replies...
Giant Scale, I am waiting for the little, fat man in the big red suit to slide down my chimney and place those 2 BIG boxes under our tree. We shall see...
I believe my RC hobby budget was opened up a bit by my financial controller (read Wife, she is the one who said to me as she was looking at a 40% Carden Extra, "why don't you build something like that?" This is just one of the reasons why I love that woman! ) so the money available for the servos is such that I should not have to gang 2 lesser torque servos on one surface. I would still like to do it though just to see it work. Maybe on another project... or on this one, who knows... I will let you know.
Justrfb
Giant Scale, I am waiting for the little, fat man in the big red suit to slide down my chimney and place those 2 BIG boxes under our tree. We shall see...
I believe my RC hobby budget was opened up a bit by my financial controller (read Wife, she is the one who said to me as she was looking at a 40% Carden Extra, "why don't you build something like that?" This is just one of the reasons why I love that woman! ) so the money available for the servos is such that I should not have to gang 2 lesser torque servos on one surface. I would still like to do it though just to see it work. Maybe on another project... or on this one, who knows... I will let you know.
Justrfb