Comp-ARF 2.3m Rudder Cable Exits
#1
Thread Starter
My Feedback: (1)
Join Date: Jul 2002
Location: SevenoaksKent, UNITED KINGDOM
Posts: 5,193
Likes: 0
Received 0 Likes
on
0 Posts
Comp-ARF 2.3m Rudder Cable Exits
Hey guys,
For those of you who have built the 2.3m Extra, did you find the positions indicated in the manual for the rudder cable exits to be spot on? If not, where should they go??
Thanks,
Mark
For those of you who have built the 2.3m Extra, did you find the positions indicated in the manual for the rudder cable exits to be spot on? If not, where should they go??
Thanks,
Mark
#2
My Feedback: (18)
Join Date: Aug 2002
Location: North Hollywood, CA
Posts: 3,713
Likes: 0
Received 0 Likes
on
0 Posts
RE: Comp-ARF 2.3m Closed Loop Exits
Hmmm, what do you mean Mark? Rudder cables? If that is what you mean, mine were way off because I have my rudder servo way up front and the geometry is not stardard. It was a drag to get right but I worked it out.
Joe
Joe
#3
Thread Starter
My Feedback: (1)
Join Date: Jul 2002
Location: SevenoaksKent, UNITED KINGDOM
Posts: 5,193
Likes: 0
Received 0 Likes
on
0 Posts
RE: Comp-ARF 2.3m Closed Loop Exits
Sorry Joe, not the clearest post I've written. Should be clearer now.
Also, I guess I should say that this question is for those who have gone with the stock setup.
Rgds,
Mark
Also, I guess I should say that this question is for those who have gone with the stock setup.
Rgds,
Mark
#6
My Feedback: (36)
RE: Comp-ARF 2.3m Rudder Cable Exits
They were way off on the 2.6 extra I know that. The way I have done it before is to mark the bottom of the fuse where the rudder servo arms are at and use a straigh edge or string to the rudder control horns and mark the verticle portion on the side of the fuse. Then mark the side of the fuse where the rudder servo horn is and intersect the lines and WHAMO! you got it. I should have done that instead of trusting there measurements. If your gonna cross the wires inside just keep that in mind when your pulling your line.
Hope this is not to hard to understand.
Tim.
Hope this is not to hard to understand.
Tim.
#7
My Feedback: (1)
Join Date: Jul 2004
Location: Perth WA, AUSTRALIA
Posts: 2,200
Likes: 0
Received 0 Likes
on
0 Posts
RE: Comp-ARF 2.3m Rudder Cable Exits
Hi Mark,
Yep, i made the mistake of carefully marking out the exact dimensions from the instructions and the exits are a fair way out.(stock set up) I read later that those dimensions are actually for the 3.0m model. No biggy,, will just fill and redo as Tim suggests. Disappointing though from such a great model.
Brad
Yep, i made the mistake of carefully marking out the exact dimensions from the instructions and the exits are a fair way out.(stock set up) I read later that those dimensions are actually for the 3.0m model. No biggy,, will just fill and redo as Tim suggests. Disappointing though from such a great model.
Brad
#9
Thread Starter
My Feedback: (1)
Join Date: Jul 2002
Location: SevenoaksKent, UNITED KINGDOM
Posts: 5,193
Likes: 0
Received 0 Likes
on
0 Posts
RE: Comp-ARF 2.3m Rudder Cable Exits
Thanks guys,
I'm not building a 2.3m myself. I have a friend who is and he doesn't have a PC so can't get to RCU - he wants to know where to cut the slots and "would rather just have the dimensions for the correct slots"
So, anyone willing to do the 2.3m equivalent of the following photo??...
I'm not building a 2.3m myself. I have a friend who is and he doesn't have a PC so can't get to RCU - he wants to know where to cut the slots and "would rather just have the dimensions for the correct slots"
So, anyone willing to do the 2.3m equivalent of the following photo??...
#10
My Feedback: (99)
Join Date: Nov 2002
Location: Suwanee,
GA
Posts: 707
Likes: 0
Received 0 Likes
on
0 Posts
RE: Comp-ARF 2.3m Rudder Cable Exits
Its not that simple, each set up is different. Servo location, servo arm width, etc...Grab some masking tape, a marker and a 3-4 foot long straight edge - measure it twice and cut it once - good luck.
#11
Thread Starter
My Feedback: (1)
Join Date: Jul 2002
Location: SevenoaksKent, UNITED KINGDOM
Posts: 5,193
Likes: 0
Received 0 Likes
on
0 Posts
RE: Comp-ARF 2.3m Rudder Cable Exits
I appreciate that - was looking for those who have built the model exactly "as per the manual" to have a quick check. Should be the same each time if the instructions are followed I guess?