Large Pusher Props
#2
My Feedback: (2)
Join Date: Jan 2002
Location: Katy,
TX
Posts: 1,648
Likes: 0
Received 0 Likes
on
0 Posts
RE: Large Pusher Props
Here you go...http://www.zingerpropeller.com/Pusher.htm
Good Luck,,,need pictures of finished monster.
I used these on one P-38 with counter rotating engines...I needed that.
Good Luck,,,need pictures of finished monster.
I used these on one P-38 with counter rotating engines...I needed that.
#3
Thread Starter
My Feedback: (38)
RE: Large Pusher Props
Twinman:
Thank you, did not know Zinger made them that big. Have never been a Zinger fan of larger props. Was hoping to find some high end props like Menz but will give it a try.
Skymaster is about 90% done. Just need to install engines, radio gear, finish prep, then paint.
Also have a Modaire Aerocommander at the vinyl shop. Hope to have pictures posted in the next few weeks. It will pop your eyes out. Great looking plane. Thanks, Paul
Thank you, did not know Zinger made them that big. Have never been a Zinger fan of larger props. Was hoping to find some high end props like Menz but will give it a try.
Skymaster is about 90% done. Just need to install engines, radio gear, finish prep, then paint.
Also have a Modaire Aerocommander at the vinyl shop. Hope to have pictures posted in the next few weeks. It will pop your eyes out. Great looking plane. Thanks, Paul
#4
My Feedback: (2)
Join Date: Jan 2002
Location: Katy,
TX
Posts: 1,648
Likes: 0
Received 0 Likes
on
0 Posts
RE: Large Pusher Props
Talked to Mezlik once about reverse pitch three blades for a P-38..they will build them, but the minimum run is around 50 units. Sorry, been there, done that.
Good Luck...and looking forward to those pictures.
Twinman
Good Luck...and looking forward to those pictures.
Twinman
#5
My Feedback: (2)
Join Date: Apr 2002
Location: Strathcona county,
AB, CANADA
Posts: 5,394
Received 0 Likes
on
0 Posts
RE: Large Pusher Props
Why not get a reverse rotation DA-50 for the back and use "normal" propellors. I know the DA-150 can be converted (at the factory) to reverse rotation, and with a simple reed induction system, it should be just a matter of moving the hall effect sensor to reverse the spark timing......I'm sure that DA could do this for you.....
#6
Thread Starter
My Feedback: (38)
RE: Large Pusher Props
Hmmmm.................. I guess I am missing something. By simply reversing the rotation of the engine and using normal propellars attached the normal way, you now have a pusher? I have heard of counter rotating engines on twins before. In those cases, the counter rotating engine is still a puller....... What am I missing here? I will certainly e-mail DA once I get this figured out...
Paul
Paul
#7
RE: Large Pusher Props
All you need is a pusher prop on the rear, normal rotation for the motor you have a pusher set up.
With a counter rotating engine facing rear a regular prop is a pusher.
A pusher prop has reversed pitch of a puller, on a forward facing counter rotating engine it is a puller.
With a counter rotating engine facing rear a regular prop is a pusher.
A pusher prop has reversed pitch of a puller, on a forward facing counter rotating engine it is a puller.
#8
My Feedback: (2)
Join Date: Apr 2002
Location: Strathcona county,
AB, CANADA
Posts: 5,394
Received 0 Likes
on
0 Posts
RE: Large Pusher Props
Hmmmm.................. I guess I am missing something. By simply reversing the rotation of the engine and using normal propellars attached the normal way, you now have a pusher?
Of course, you have to mount the prop so that the blunt leading edge is still facing the front of the plane
#13
My Feedback: (2)
Join Date: Jan 2002
Location: Katy,
TX
Posts: 1,648
Likes: 0
Received 0 Likes
on
0 Posts
RE: Large Pusher Props
Hey Paul http://www.zingerpropeller.com/3_bladed_Propeller.htm
And you can have three blade pusher..Just found for "Special" project!!
And you can have three blade pusher..Just found for "Special" project!!
#15
My Feedback: (2)
Join Date: Apr 2002
Location: Strathcona county,
AB, CANADA
Posts: 5,394
Received 0 Likes
on
0 Posts
RE: Large Pusher Props
Decided to use the xoar pusher instead of reversing the engine.