LED Lights?
#1
Thread Starter
Join Date: Mar 2007
Location: Sarasota, FL
Posts: 3,671
Likes: 0
Received 0 Likes
on
0 Posts
LED Lights?
I went out and bought some LED lights at radio shack to play around with. But when i connect them to a 9v battery the will turn on bright for a couple of seconds then fade and burn out. It seems to me that to much power is getting to the lite and killing? Any help would be great. Thanks
#4
Thread Starter
Join Date: Mar 2007
Location: Sarasota, FL
Posts: 3,671
Likes: 0
Received 0 Likes
on
0 Posts
RE: LED Lights?
I assume this [link=http://resistor]http://www.radioshack.com/product/index.jsp?productId=2062347&cp=&sr=1&origkw=10k+oh m+resistor&kw=10k+ohm+resistor&parentPage=search[/link] would work? Just how do i wire it exactly would i do it if i used 1 9v battery with a red and black wire comming out and then 4 small led lights.
THanks
Nick
THanks
Nick
#5
Senior Member
Join Date: Oct 2006
Location: Valley Springs,
CA
Posts: 4,897
Likes: 0
Received 0 Likes
on
0 Posts
RE: LED Lights?
That 9v is way too much for those LEDs. I believe that the LEDs from Radioshack handle up to 4 volts; which is what most LEDs can.
There are two ways to do this; series or parallel. If you do it in series, each light connected to the other will be dimmer, because the one before that is drawing the power. If you do it by parallel, it should all be even, but not as bright as possible. If you do it by series, you run 1 resistor; if you run it by parallel, you run a resistor to each LED. The parallel has more material, but the outcome will be the best.
There are two ways to do this; series or parallel. If you do it in series, each light connected to the other will be dimmer, because the one before that is drawing the power. If you do it by parallel, it should all be even, but not as bright as possible. If you do it by series, you run 1 resistor; if you run it by parallel, you run a resistor to each LED. The parallel has more material, but the outcome will be the best.
#6
Thread Starter
Join Date: Mar 2007
Location: Sarasota, FL
Posts: 3,671
Likes: 0
Received 0 Likes
on
0 Posts
RE: LED Lights?
So basically the resiator will bring the volts down so that i can use the 9v battery? Also the resiators i found above would work good?
Thanks for the help.
Thanks for the help.
#7
Senior Member
Join Date: Oct 2006
Location: Valley Springs,
CA
Posts: 4,897
Likes: 0
Received 0 Likes
on
0 Posts
#8
Thread Starter
Join Date: Mar 2007
Location: Sarasota, FL
Posts: 3,671
Likes: 0
Received 0 Likes
on
0 Posts
#9
Senior Member
Join Date: Oct 2006
Location: Valley Springs,
CA
Posts: 4,897
Likes: 0
Received 0 Likes
on
0 Posts
RE: LED Lights?
Yeah 10k will work, I'm thinking that you can go a little lower, but I'm spacing on my electronics knowledge right now...
Here's a diagram I made; a bit rough but it should do. I'd rather use parallel so each LED gets the same amount of voltage, and not have each LED after the next be dimmer.
Here's a diagram I made; a bit rough but it should do. I'd rather use parallel so each LED gets the same amount of voltage, and not have each LED after the next be dimmer.
#11
Senior Member
Join Date: Jan 2006
Location: grand junction, CO
Posts: 834
Likes: 0
Received 0 Likes
on
0 Posts
RE: LED Lights?
He doesn't need a resistor for each LED in series. Yea, he can use less than a 10k, a 1k would do the trick too. You can wire it up like this:
Code:
-----\/\/\/\/-------------------------- | | | | | | - --- --- --- ^ ^ - | | --- | | | | | ---------------------------------------
#13
Senior Member
Join Date: Apr 2007
Location: Thousand Oaks,
CA
Posts: 8,958
Likes: 0
Received 0 Likes
on
0 Posts
RE: LED Lights?
I use a 1k in series paralel with a square of lights for a different aplication and the time that I have run the LED's (white) for they are not warm at all. Just thought it would help. LED are the best for lights on an RC because they don't have a fillament that can burn out.
#17
Thread Starter
Join Date: Mar 2007
Location: Sarasota, FL
Posts: 3,671
Likes: 0
Received 0 Likes
on
0 Posts
RE: LED Lights?
ORIGINAL: mattnin
For the 120VAC you are going to need an AC to 12V DC converter
For the 120VAC you are going to need an AC to 12V DC converter
Thanks