RCU Forums - View Profile: gary3173

Go Back  RCU Forums >
Reload this Page >

gary3173's Profile

Community
Search
Notices

gary3173 gary3173 is offline

About Me

  • About gary3173
    Location
    North Platte, NE

Statistics

Total Posts
Visitor Messages
Total Likes
General Information
  • Last Activity: 03-20-2022 11:27 AM
  • Join Date: 06-05-2011

Friends

Showing Friends 1 to 1 of 1

Visitor Messages

Showing Visitor Messages 1 to 10 of 13
  1. 06-20-2019 07:50 AM
    sold and shipped priority Mail
  2. 03-30-2019 03:12 PM
    You should have payment by now. Thank You, Gary
  3. 03-30-2019 11:41 AM
    Could not find you on Pay Pal. Please send an invoice. my email is the same as my pay pal. [email protected] Gary Patterson, 215 Regency Lane, North Platte, NE 69101 Thank You., Gary
  4. 03-30-2019 11:32 AM
    My email is the same as my pay pal [email protected] I will take you up on that deal.
  5. Aussie Maddog
    03-30-2019 11:27 AM
    I can't seem to upload pics here.
    This is what it tells me your email address is "[email protected]"
    I receive this fault:

    Address not found

    Your message wasn't delivered to [email protected]because the address couldn't be found, or is unable to receive mail.
  6. Aussie Maddog
    03-30-2019 11:20 AM
    Hello Gary, I received your email fine, but could not reply.

    Hello Gary,
    I have 3 modules you can have. (All for 10mm plugs)I have not flown rc or played with engines for 10 yrs now so I cannot remember much about them. One has "SUS" written on it so it may not work.
    I have a heap of hall sensors with different mounts and brackets also. Manual Kill switches (3) & new great planes switch & charge mounts (2)
    Note: There is no mounting ring for the hall sensor to to the G2300 engine.
    Back when I did this, there was no rc ignition modules to fit the 1/4 sparkplug so I went with the 10mm cm6 type. From memory, I had to mount a spacer (washer)under the plug so it didn't sit too deep.
    I'm happy to add everything in the pics. As the engine by itself weighs 1.48 kgs, it sits just under the 1.5 kg shipping rate. With the modules etc it goes up into the 2 kg rate. So I need to ask for 10 USD extra to cover the extra shipping. So $180 usd all up.
    Regards,
    Rhett
  7. 03-30-2019 08:34 AM
    Do you have the ignition module and the magnet sensor and mount? I'm scratch building a 94" P-38 Lightning I will be using the ST 2300s and will convert to ignition. Why did you adapt it to a C6 plug instead of using a 1/4 x 32 spark plug? Did you have Piston clearance problems with the C6 plug? I would take it with the used muffler if you have the module and sensor for the same price. Thanks for your time, Gary
  8. Aussie Maddog
    03-30-2019 07:57 AM
    Hello Gary, The reply to your email keeps bouncing. ....tried 3 times.
  9. 03-30-2019 05:28 AM
    Sent you an email via gmail. Thanks, Gary
  10. Aussie Maddog
    03-29-2019 06:19 PM
    Hello Gary,
    I can do $170 USD including tracked shipping by direct paypal payment to [email protected]
    (or I can invoice your paypal)
    Regards,
    Rhett Mitchell

Contact Us - Manage Preferences Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.