motodude11

My Feedback: (1)

Hey guy's
I'm lookin at a couple different engines and i need some advice in the $120-150 price range, im considering a STS .28, Losi m26ss, Axial .28, Ofna force .28, or dynamite mach .26 or .28 any of these would go in a warhead evo. Not looking for insane power looking for more reliable and a little more powerful than the stock evo engine. Don't want something that will shred my tranny or CVD any help is appriated.

Thanks
Josh

annie_himself

The Mach in the LST2 should be perfect.

motodude11

My Feedback: (1)

anyone know anything about the sts?

motodude11

My Feedback: (1)

how about a sportwerks .26 v2? anyone?

Dokioto

The Axial .28 sounds great from what I have heard.

motodude11

My Feedback: (1)

yea i know but i know where to get the sportwerks for the same price and i've heard that the sportwerks has more power

Dokioto

But will your truck handle it? If you want some serious power for a good prise take a look here- http://www3.towerhobbies.com/cgi-bin...&I=LXPEB7&P=ML

motodude11

My Feedback: (1)

i dont wanna go with that big of an engine trying to keep it either a .26 or a .28

soulreaver0102

hey Dokioto what do you need to bilt that in the warhead do you know i put a o.s 30 vg in mine and needed the ofna bolt kit for the clutch bell anyways is that a great motor or do you know

motodude11

My Feedback: (1)

got a sportwerks .26 v2

[email protected]

i put the mach .26 ss in my warhead it was great til the tranny took a crap for the 4Th time i see why they (druatraxx) put that whippie super kitten in this thing because they knew that the tranny sucked and can't take any real hp. plastic gears on the inside i dont know how anyone that has put big power in the warhead has been able to run it for anytime at all this is my 4th tranny they just dont stay together if anyone know of any upgrade for the tranny in the warhead please let me know but the mach .26 ss engine that i put in off my aftershock bring the warhead to life wheelies on demand for a block with wheelie bar but the tranny won't last long at all about 4 tanks is all i got out of it[&o]

meljon

I have a Axial .32 in mine with Proline beadlocks with Big Joes mounted. Mine is holding up good. Maybe you need to lossen up ypur slipper or adjust your clutch.

motodude11

My Feedback: (1)

Heres the final result got the sportwerks 26 v2 with an ht pipe!!

davido666

Have you run the engine, how fast does it go now. How easy was it to drop in. Any modifcatons required. I notice you still have the plastic spur gear. Are you going to put in the metal spur gear?

motodude11

My Feedback: (1)

Yes i have run it just started breaking it in, got 3 tanks in it. It is insane this motor is sick!!!!! The super stinker has nothing on this motor it actually the motor from an lst and i can see why losi dropped it in the lst!!! It took no modifications just dropped right in. and no i do not plan to use the metal spur gear unless i have too. The metal spur gear is alot heavier than the plastic one and makes the trucks a little sluggish, so if i can get away with using the plastic one im gunna stick with it, plus i have like 5-6 of them laying around if the one on the truck goes. Another thing about this engine is it runs great it ran around 150-200 degrees!! It was only 200 when i started hammering it a little more and i believe it will hang wheelies once its broken in. best mod by far for this truck!!!

motodude11

My Feedback: (1)

I take that back there were two small mods i had to do i had to dremel out a small spot underneath on the skidplate on the middle rear of the chassis for the spin start and i had to dremel out a little half moon on the chassis for the pipe

rollz247

Whasup guys,

Sorry to bring up an old thread but i'm thinkin about doin the same thing on my warhead but can't find the sportwerks .26 in stock anywhere. Any suggestions?</p>