Controlling AUX1 channel w/switch DX8
#1
Thread Starter
Controlling AUX1 channel w/switch DX8
I'm putting a Zenoah G-38 in my Midwest AT-6 and want to use AUX 1 (only channel left) on a switch to control my choke. This is on a DX8 with an AR7000 receiver. I can't figure out how to assign a 3 position switch (preferrably AUX 2) to the AUX 1 channel on the receiver.
Any help appreciated
bigbird<br type="_moz" />
Any help appreciated
bigbird<br type="_moz" />
#2
My Feedback: (2)
RE: Controlling AUX1 channel w/switch DX8
ORIGINAL: bigbird007
I'm putting a Zenoah G-38 in my Midwest AT-6 and want to use AUX 1 (only channel left) on a switch to control my choke. This is on a DX8 with an AR7000 receiver. I can't figure out how to assign a 3 position switch (preferrably AUX 2) to the AUX 1 channel on the receiver.
Any help appreciated
bigbird<br type=''_moz'' />
I'm putting a Zenoah G-38 in my Midwest AT-6 and want to use AUX 1 (only channel left) on a switch to control my choke. This is on a DX8 with an AR7000 receiver. I can't figure out how to assign a 3 position switch (preferrably AUX 2) to the AUX 1 channel on the receiver.
Any help appreciated
bigbird<br type=''_moz'' />
#5
Thread Starter
RE: Controlling AUX1 channel w/switch DX8
I know about assigning switches, I just couldn't get Aux 2, 3 position switch to show up. I assume I have to do a mix Aux1 to Aux1 but Aux2 wasn't in the switch assignment list...I'll try again with the flap system inhibited and post the results.Thanks Richbigbird
#6
Thread Starter
RE: Controlling AUX1 channel w/switch DX8
It turns out that the flap system was inhibited. I got it to work on the mix switch with settings of:
Mix 1
Aux1 > Aux1
Rate -87
+122
Offset -100
Trim Inh
SW: mix1
Seems to work but I would like it on Aux2 Gov switch so I could have a three position switch for Off - half choke - full choke.
Any ideas?
Thanks for any help
bigbird
Mix 1
Aux1 > Aux1
Rate -87
+122
Offset -100
Trim Inh
SW: mix1
Seems to work but I would like it on Aux2 Gov switch so I could have a three position switch for Off - half choke - full choke.
Any ideas?
Thanks for any help
bigbird
#7
My Feedback: (2)
RE: Controlling AUX1 channel w/switch DX8
ORIGINAL: bigbird007
It turns out that the flap system was inhibited. I got it to work on the mix switch with settings of:
Mix 1
Aux1 > Aux1
Rate -87
+122
Offset -100
Trim Inh
SW: mix1
Seems to work but I would like it on Aux2 Gov switch so I could have a three position switch for Off - half choke - full choke.
Any ideas?
Thanks for any help
bigbird
It turns out that the flap system was inhibited. I got it to work on the mix switch with settings of:
Mix 1
Aux1 > Aux1
Rate -87
+122
Offset -100
Trim Inh
SW: mix1
Seems to work but I would like it on Aux2 Gov switch so I could have a three position switch for Off - half choke - full choke.
Any ideas?
Thanks for any help
bigbird
#8
RE: Controlling AUX1 channel w/switch DX8
On the Switches screen, you can only assign 1 source to a channel, so you would need to de-assign another device from Aux1 before you could put another there. Depending on your wing type, that might not work because it would already be owned by, say, the left aileron or by the flaps.
Andy
Andy
#9
My Feedback: (2)
RE: Controlling AUX1 channel w/switch DX8
ORIGINAL: BuschBarber
I was looking at my DX8, but I was not sure if I could assign the Aux2 switch to Aux1.
ORIGINAL: bigbird007
It turns out that the flap system was inhibited. I got it to work on the mix switch with settings of:
Mix 1
Aux1 > Aux1
Rate -87
+122
Offset -100
Trim Inh
SW: mix1
Seems to work but I would like it on Aux2 Gov switch so I could have a three position switch for Off - half choke - full choke.
Any ideas?
Thanks for any help
bigbird
It turns out that the flap system was inhibited. I got it to work on the mix switch with settings of:
Mix 1
Aux1 > Aux1
Rate -87
+122
Offset -100
Trim Inh
SW: mix1
Seems to work but I would like it on Aux2 Gov switch so I could have a three position switch for Off - half choke - full choke.
Any ideas?
Thanks for any help
bigbird
#11
Thread Starter
RE: Controlling AUX1 channel w/switch DX8
Thanks Andy,
I'll look but I don't believe that anything else is assigned. I have no flaps and a Y on the ailerons. I do have dual elevators but the other channel is in Aux 2.
Perhaps I need to rearrange and use Aux2 for the choke and Aux1 for the other half of the elevator?
Thanks,
bigbird<br type="_moz" />
I'll look but I don't believe that anything else is assigned. I have no flaps and a Y on the ailerons. I do have dual elevators but the other channel is in Aux 2.
Perhaps I need to rearrange and use Aux2 for the choke and Aux1 for the other half of the elevator?
Thanks,
bigbird<br type="_moz" />
#12
My Feedback: (2)
RE: Controlling AUX1 channel w/switch DX8
ORIGINAL: bigbird007
Could you detail how you did that Rich?<div>
</div><div>Thanks</div><div>
</div><div>bigbird</div>
Could you detail how you did that Rich?<div>
</div><div>Thanks</div><div>
</div><div>bigbird</div>
#13
Thread Starter
RE: Controlling AUX1 channel w/switch DX8
You enter the System Menu by holding down the Roller and turning on the Tx. Scroll down to Switch Select. Scroll to Aux2 and change the value for the channel to Aux1.
I guess I never needed to change the switch selection in the system menu before, I didn't realize it was there. I'd always been able to change it to what I needed in the function menu.
Thanks a million!
bigbird
Update: Well there was a simple solution, I called Horizon and was told to go into the function menu/servo setup/subtrim for aux1 and adjust as needed. It works!<br type="_moz" />