3D Printable 1/16 RC Tanks
#151
Thread Starter
2S7 "Pion
https://cults3d.com/en/3d-model/various/2s7-pionhttps://en.wikipedia.org/wiki/2S7_Pion
Thanks
Jimmy
The following 2 users liked this post by bowlman:
maillemaker (04-04-2024),
tankme (04-04-2024)
#152
Thread Starter
M24 Chaffee
https://cults3d.com/en/3d-model/various/m24-chaffee-rc_3d_tankshttps://en.wikipedia.org/wiki/M24_Chaffee
Jimmy
The following 3 users liked this post by bowlman:
#153
Thread Starter
CV9040C
https://cults3d.com/en/3d-model/various/cv9040chttps://en.wikipedia.org/wiki/Combat_Vehicle_90
Jimmy
The following users liked this post:
Davepriddy14 (06-08-2024)
#154
Thread Starter
CV90120
https://cults3d.com/en/3d-model/various/cv90120-rc_3d_tanks?fbclid=IwZXh0bgNhZW0CMTEAAR0V3uAPAZ5zb LPVkVvihWzDYAj0jHFypP-4RsznA0IRP2QSqoSAHhHAwUs_aem_AXQhxvra9WDKjTiBNhkic aMxHxbdddCKF5KyGd_zQGq6BFsHS-asuCvXtpkzewEpL3XgroL0gdMW-uShAZZmM8Fqhttps://tanks-encyclopedia.com/modern/swedish/cv90120/
Thanks
Jimmy
The following users liked this post:
Davepriddy14 (06-08-2024)
#155
Thread Starter
1/16 compatible K2 Blackpanther turret
https://cults3d.com/en/3d-model/art/...MxdJ1grvih5uXb
Thanks
Jimmy
The following users liked this post:
Davepriddy14 (06-08-2024)
#156
Thread Starter
Type 95 Ha-Go
https://en.wikipedia.org/wiki/Type_95_Ha-Go_light_tankThanks
Jimmy
#158
Thread Starter
https://cults3d.com/en/3d-model/various/vt1-2
Thanks
Jimmy
VT1-2
https://www.youtube.com/watch?v=e82xD2xcagYThanks
Jimmy
Last edited by bowlman; 06-23-2024 at 05:48 PM.
#159
Thread Starter
Kranvagn
https://cults3d.com/en/3d-model/various/kranvagnhttps://en.wikipedia.org/wiki/Emil_(tank)
Jimmy
#160
Thread Starter
Challenger 2 AFU
https://cults3d.com/en/3d-model/various/challenger-2-afuhttps://en.wikipedia.org/wiki/Challenger_2
Thanks
Jimmy
#161
Thread Starter
For them that have the HL Challenger 2 you can print the cage and its mounts and add it to your tank
#162
Thread Starter
#163
Thread Starter
M48A1 Patton
https://cults3d.com/en/3d-model/various/m48-pattonhttps://en.wikipedia.org/wiki/M48_Patton
https://rc3dtanks.site/detail.html#m48
Jimmy
Last edited by bowlman; 08-21-2024 at 11:03 AM.
The following users liked this post:
tankme (08-21-2024)
#164
Thread Starter
Looking at the detail page the back of the tank looks like you could print the M60 back end and the engine deck top to make a M48A2 or an A3 ill have to look more to see if the only difference is just the front of the M48 from a M60 to make a M48A5 they look close I think the hull tub is the same shape other then the front the build looks the same as the M60.
Thanks
Jimmy
Thanks
Jimmy
#165
Thread Starter
#166
Since the M60 was already in the models he designed, a lot of us requested the original M48 as you are correct that the upgraded M48 uses the M60 engine deck. I've printed Inkor's M60 and the deck can easily be removed, but I'm not sure what changes would have to happen to adapt it to make a later M48 model. I'm sure some smart slicer cutting and pasting could adapt the M60 rear end and upper deck. I have plans to print the M48 after I finish printing my Warprints Cromwell so I can compare the two, but it will probably be a few weeks before I get to that point.
#167
Thread Starter
Since the M60 was already in the models he designed, a lot of us requested the original M48 as you are correct that the upgraded M48 uses the M60 engine deck. I've printed Inkor's M60 and the deck can easily be removed, but I'm not sure what changes would have to happen to adapt it to make a later M48 model. I'm sure some smart slicer cutting and pasting could adapt the M60 rear end and upper deck. I have plans to print the M48 after I finish printing my Warprints Cromwell so I can compare the two, but it will probably be a few weeks before I get to that point.
I was also one requesting the M48 I for got there was two versions of the rear .
Thanks
Jimmy
#168
Yeah, with the combo of all the M60/M48 turrets and both rear ends, I think we can cobble together whatever version of the M48 or M60 we want to build now except the M60A2 which DKLM RC has a conversion kit for the TongDE.
#169
Thread Starter
Thanks
Jimmy
Last edited by bowlman; 08-21-2024 at 01:45 PM.
#170
Contact Richard directly about the tracks. I bought a set from him not too long ago and they weren't listed on his site. Motion RC does carry the plastic tracks, but they seem to be sold out at the moment.
#171
Thread Starter
Thanks
jimmy
#172
Rich is good people! Buy with confidence he is definitely trustworthy. I buy from him routinely and have never been disappointed in his product or service. His custom M60 accessories are all top notch products.
#173
Thread Starter
I got his M60 accessories kit a few weeks ago on ebay for the printed M60 I did .
Thanks
Jimmy
#174
Thread Starter
Just printed the M60 rear section and the M48 section 5 they wont line up
#175
Inkor was on the Discord server today saying he didn't think it would and that the M48 had slightly different dimensions than the M60.