For sale: Goldberg Ultimate local pickup Acworth GA USA
#1
Senior Member
Thread Starter
My Feedback: (2)
Join Date: Apr 2020
Location: Metro Atlanta GA, USA
Posts: 449
Likes: 0
Received 36 Likes
on
32 Posts
For sale: Goldberg Ultimate local pickup Acworth GA USA
Local pickup only. No shipping - please don't even ask.
Goldberg Ultimate biplane, built from downloaded plans from the original kit. Used balsa in fuselage, instead of lite-ply, so it is lighter than the original kitted plane. Weighs 9 lb, 6 oz with Saito 100. Saito 100 is too light, and I don't put lead in airplanes, so this needs a heavier 120 engine. I don't want to buy another engine. Saito 100 is NOT included!
I have built over 50 kits during the last 40 years. Covered in Ultracote. Cowl and wheel pants from Fiberglass Specialties, and clearcoated with very fuel-resistant clear System Three Topcoat. Landing gear from TNT landing gear. 12 oz fuel tank.
Includes:
Spektrum 6-channel receiver. Bind-n-fly with your Spektrum transmitter, which means no transmitter included
HS-645MG servo on pull-pull rudder
HS-545MG servo on pushrod elevator
HS-485MG servos on bottom ailerons. Top ailerons controlled with pushrods coming up from bottom ailerons
HS-82MG servo on throttle
Aluminum spinner
Bolt on a heavier engine, bind RX to your TX, and it is ready to fly. Has been taxied in my driveway, but not flown yet. I will remove the current Saito 100, when sold.
Can be seen at Cobb County RC field, with an appointment, or at my house in Acworth, GA
$500 (the wood alone was ~$400)
.
Please keep in mind that this is a For Sale ad, and NOT a discussion forum thread. General questions are ok, but make offers in a Private Message, and for gawd's sake, do not EVER post your contact info in an internet thread.
Goldberg Ultimate biplane, built from downloaded plans from the original kit. Used balsa in fuselage, instead of lite-ply, so it is lighter than the original kitted plane. Weighs 9 lb, 6 oz with Saito 100. Saito 100 is too light, and I don't put lead in airplanes, so this needs a heavier 120 engine. I don't want to buy another engine. Saito 100 is NOT included!
I have built over 50 kits during the last 40 years. Covered in Ultracote. Cowl and wheel pants from Fiberglass Specialties, and clearcoated with very fuel-resistant clear System Three Topcoat. Landing gear from TNT landing gear. 12 oz fuel tank.
Includes:
Spektrum 6-channel receiver. Bind-n-fly with your Spektrum transmitter, which means no transmitter included
HS-645MG servo on pull-pull rudder
HS-545MG servo on pushrod elevator
HS-485MG servos on bottom ailerons. Top ailerons controlled with pushrods coming up from bottom ailerons
HS-82MG servo on throttle
Aluminum spinner
Bolt on a heavier engine, bind RX to your TX, and it is ready to fly. Has been taxied in my driveway, but not flown yet. I will remove the current Saito 100, when sold.
Can be seen at Cobb County RC field, with an appointment, or at my house in Acworth, GA
$500 (the wood alone was ~$400)
.
Please keep in mind that this is a For Sale ad, and NOT a discussion forum thread. General questions are ok, but make offers in a Private Message, and for gawd's sake, do not EVER post your contact info in an internet thread.
#2
My Feedback: (179)
Join Date: Mar 2002
Location: Orange, CA
Posts: 90
Likes: 0
Received 0 Likes
on
0 Posts
Biplane
You are a Master builder the kit was hard enough to build, but to scratch build one. Sweet looking. I had a YS 120 in the one I built plenty of power and the weight was just about perfect.