Which canister for Evolution/MVVS 45
#1
Senior Member
Thread Starter
Join Date: Mar 2005
Location: Copenhagen, DENMARK
Posts: 361
Likes: 0
Received 0 Likes
on
0 Posts
Which canister for Evolution/MVVS 45
Which canisters do you recommend for an Evolution/MVVS 45. I have read a bit on the topic and it seems the length of the header is of great importance. How do you figure the optimum length?
Also, as a main rule, is a bigger can better?
I've been looking on Krumscheid's (KS's) 88 VS-4 or 86 VS-4. Is it an advantage to pick the 88 mm for best performance?
http://www.krumscheid-metallwaren.de...EN&anr=88+VS-4
I also need a header and though of this:
http://www.krumscheid-metallwaren.de...=EN&anr=1525-2
What about MTW (http://www.mtw-daempfer.de). How do they perform compared to KS?
The engine is going in a H9 Extra 260 and is going to have the cylinder hanging like the picture below. Any suggestions or perferably experience for a well performing set up with this engine?
Also, as a main rule, is a bigger can better?
I've been looking on Krumscheid's (KS's) 88 VS-4 or 86 VS-4. Is it an advantage to pick the 88 mm for best performance?
http://www.krumscheid-metallwaren.de...EN&anr=88+VS-4
I also need a header and though of this:
http://www.krumscheid-metallwaren.de...=EN&anr=1525-2
What about MTW (http://www.mtw-daempfer.de). How do they perform compared to KS?
The engine is going in a H9 Extra 260 and is going to have the cylinder hanging like the picture below. Any suggestions or perferably experience for a well performing set up with this engine?
#2
Join Date: Apr 2002
Location: NETHERLANDS
Posts: 668
Likes: 0
Received 0 Likes
on
0 Posts
RE: Which canister for Evolution/MVVS 45
Tor, perhaps these threads are usefull?
http://www.rcuniverse.com/forum/m_35...tm.htm#3593225
http://www.rcuniverse.com/forum/m_32...ey_mvvs/tm.htm
I will be using the 86 Krumscheid cannister next spring, have no figures for comparison however.
http://www.rcuniverse.com/forum/m_35...tm.htm#3593225
http://www.rcuniverse.com/forum/m_32...ey_mvvs/tm.htm
I will be using the 86 Krumscheid cannister next spring, have no figures for comparison however.
#3
Senior Member
Thread Starter
Join Date: Mar 2005
Location: Copenhagen, DENMARK
Posts: 361
Likes: 0
Received 0 Likes
on
0 Posts
RE: Which canister for Evolution/MVVS 45
Hi Hans
Thanks for the links... Have you run yours yet with the KS can?
What about header length? Is there anywhere to find information about what the length of the header should be for maximun efficiency?
Thanks for the links... Have you run yours yet with the KS can?
What about header length? Is there anywhere to find information about what the length of the header should be for maximun efficiency?
#4
Join Date: Apr 2002
Location: NETHERLANDS
Posts: 668
Likes: 0
Received 0 Likes
on
0 Posts
RE: Which canister for Evolution/MVVS 45
ORIGINAL: Tor
Thanks for the links... Have you run yours yet with the KS can?
Thanks for the links... Have you run yours yet with the KS can?
ORIGINAL: Tor
What about header length? Is there anywhere to find information about what the length of the header should be for maximun efficiency?
What about header length? Is there anywhere to find information about what the length of the header should be for maximun efficiency?