1/8 bud steering trouble
#1
Junior Member
Thread Starter
My Feedback: (1)
Join Date: May 2005
Location: , MO
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
1/8 bud steering trouble
I took out the old jr 270 steering servos and replaced them with one jr z650 m at 123oz of torque at 4.5 volts 142 at 6 volts ,and i'm still having steering trouble. Does anyone no how much torque it takes to turn a 1/8 miss bud ?
#4
Senior Member
Join Date: Nov 2005
Location: Snellville,
GA
Posts: 505
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/8 bud steering trouble
It sounds to me like you went from a pull-pull set-up to a push pull set-up. If the rod is to small in diameter, it may be flexing at hi pressure loads and not turning the boat. either use a thicker rod to steer it or if you can set up a differant configuration of pull-pull steering using the single servo.
#5
Junior Member
Thread Starter
My Feedback: (1)
Join Date: May 2005
Location: , MO
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/8 bud steering trouble
The steering trouble i'm having is the boat doesn't want to turn at higher speeds it should make right turns on a dime . The guy from Twisted Liquid said if you hold the rudder and turn the controller the servo should be strong enough to move the boat but it doesn't and the push rod isn't flexing . Help!!!!!!!!
#6
Senior Member
Join Date: Sep 2005
Location: Mildura, AUSTRALIA
Posts: 2,056
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/8 bud steering trouble
Check if you have a BEC receiver, if you do you need a Y connector to hook the battery power to both the servo and receiver. Are you sure the batteries are good? What kind and how many batteries are you using?
#10
RE: 1/8 bud steering trouble
Sounds like a radio/battery problem to me. If you're not getting any binding and the problem is only at higher speeds, you might try a bigger battery pack and see what happens. How old is the battery pack you are using?
#11
Junior Member
Join Date: Feb 2007
Location: perthwestern australia, AUSTRALIA
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/8 bud steering trouble
The steering trouble i'm having is the boat doesn't want to turn at higher speeds it should make right turns on a dime
Dont get me wrong here im not having a go but if you guys are getting these boats to turn on dimes your doing real well there design is that of a skater thats why they have a large turn fin on the predominant side of turning IE: right if the boat is mostly turning right
here in australia our track layout is full oval on a right hand turn 100 metre lengh and we need every bit of about 15 metre turning area
Personaly i would make sure your rudder is capable of pushing this boat around make sure your turn fin is adiquate and as one of the other guys mentioned look for any binding in control rods or lines if so free em up and use a good quality grease like bel ray water proof high temp grease
Cheers ian
Dont get me wrong here im not having a go but if you guys are getting these boats to turn on dimes your doing real well there design is that of a skater thats why they have a large turn fin on the predominant side of turning IE: right if the boat is mostly turning right
here in australia our track layout is full oval on a right hand turn 100 metre lengh and we need every bit of about 15 metre turning area
Personaly i would make sure your rudder is capable of pushing this boat around make sure your turn fin is adiquate and as one of the other guys mentioned look for any binding in control rods or lines if so free em up and use a good quality grease like bel ray water proof high temp grease
Cheers ian
#13
Member
Join Date: Oct 2005
Location: RSM,
CA
Posts: 69
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/8 bud steering trouble
Check out my rudder and turn fin set-up. The boat handles like it's on rails. . . . . no issues with cornering and a added plus is the huge rooster it kicks up with the modded turn-fin when making turns.
http://www.rcuniverse.com/forum/m_4900779/tm.htm
http://www.rcuniverse.com/forum/m_4900779/tm.htm
#14
Senior Member
Join Date: Jan 2003
Location: Helsingborg, SWEDEN
Posts: 929
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/8 bud steering trouble
ORIGINAL: markfs
It's a R135 Jr Fm, the receiver the came with the boat and i put 6 volts to it
It's a R135 Jr Fm, the receiver the came with the boat and i put 6 volts to it
Sorry it's so big I can't get a thumbnail to work [:@]
Do you have a picture of your setup?