Gas RC Jet Boat
#4
RE: Gas RC Jet Boat
Twin craft boats here in the states is just finishing up the 32" x 15" 1/4 scale Jet Sprint Mold and hulls should be available very soon for a very reasonable cost....I handle the Swash drive Stainless Steel hydro jet pump. The hydro jet pumps run about $600 delivered. they put out close to 60 pounds of thrust and speeds near 45 mph. here is a link you can visit showing the pump and hull [link=http://groups.msn.com/JetSprintRC/rcjetsprint.msnw]JetSprintR/C link[/link]
#5
Thread Starter
My Feedback: (1)
Join Date: Jun 2004
Location: Culpeper,
VA
Posts: 254
Likes: 0
Received 0 Likes
on
0 Posts
RE: Gas RC Jet Boat
Fastrat...Thanks of the info. I'll be waiting to see how the twin craft boat turns out. I would really like to have a boat like [link=http://www.swashdrive.com.au/phpBB2/viewtopic.php?t=113]this.[/link]
#6
RE: Gas RC Jet Boat
THe hull you linked to at Swashdrive is the exact hull Twincraft is producing with Roll bars and driver figures are built in oregon. Just the nature of these unique jetsprint boats and there tight maneuverability means a low cost stock engine can yield tons of fun.
#8
RE: Gas RC Jet Boat
JImmy the owner of Twincraft is very busy and is workin every spare moment on the jetsprint hull and it will be relased very soon. we were talkin about $150 price range for the hull ,,,,,so stay tuned
#11
RE: Gas RC Jet Boat
The newly redesigned jet sprint hull molds are at he had reworked the deck and the bottom a bit from the original design [link=http://groups.msn.com/SCORPIONMARINERCBOATS]Scorpion Marine RC Boats[/link]
you can get in touch with him over at RC boat world site
PM me for a link cuz i think they disallowed it last time i posted it
here is the hull with a swash drive roll bar
[link=http://groups.msn.com/SCORPIONMARINERCBOATS/jetboatpics.msnw?action=ShowPhoto&PhotoID=88]Scorpion Marines web site[/link]
you can get in touch with him over at RC boat world site
PM me for a link cuz i think they disallowed it last time i posted it
here is the hull with a swash drive roll bar
[link=http://groups.msn.com/SCORPIONMARINERCBOATS/jetboatpics.msnw?action=ShowPhoto&PhotoID=88]Scorpion Marines web site[/link]
#12
Senior Member
Join Date: Feb 2008
Location: Old Hangtown ,
CA
Posts: 851
Likes: 0
Received 0 Likes
on
0 Posts
RE: Gas RC Jet Boat
Here are a few shots of one I did a few years ago. Swashdrive pump into a 47" Microburst V bottom mono.
First powered by a Zen 26, then onto a Quickdraw 25 ..... Really fun boat !!
First powered by a Zen 26, then onto a Quickdraw 25 ..... Really fun boat !!
#14
Member
Join Date: Aug 2003
Location: brisbane, , AUSTRALIA
Posts: 84
Likes: 0
Received 0 Likes
on
0 Posts
RE: Gas RC Jet Boat
Heah Dirtracer
I sent you an email regarding the sprint with pricing etc,
but your ISP bounced my email back saying reply denied because of abuse ????
I don't get abusive at all, so it must be all the spam floating through my ISP.
The only thing i can suggest is Change ur ISP or send me a PM
Kindest regards
Craig
I sent you an email regarding the sprint with pricing etc,
but your ISP bounced my email back saying reply denied because of abuse ????
I don't get abusive at all, so it must be all the spam floating through my ISP.
The only thing i can suggest is Change ur ISP or send me a PM
Kindest regards
Craig