Vision 3D release date
#1
Senior Member
Thread Starter
Join Date: Apr 2004
Location: sarasota,
FL
Posts: 118
Likes: 0
Received 0 Likes
on
0 Posts
Vision 3D release date
hey chip when can we expect to see your vision 3d for sale i got a DA 50 all ready for it what kind of torq do i need for my surfaces. is the wing a plug in.
thx
Ben
[email protected]
thx
Ben
[email protected]
#2
My Feedback: (18)
Join Date: Aug 2002
Location: North Hollywood, CA
Posts: 3,713
Likes: 0
Received 0 Likes
on
0 Posts
RE: Vision 3D release date
Since Chip is not responding to anything on this board, has anyone called chief and asked about the Vision 3D? They have it listed for sale. I may call early next week.
Joe
Joe
#5
My Feedback: (8)
RE: Vision 3D release date
THe Visions will be released next week. They are due in toward the end of this week. I am sorry for the delayed responses, I have been going non-stop for the past 2 months and just have not been able to get everything done that I needed to. Looks like a light at the end of the tunnel now and I will get back to the forum when the shootout is over on a regular basis. Sorry about the inconvienance
Chip
Chip
ORIGINAL: invme
hey chip when can we expect to see your vision 3d for sale i got a DA 50 all ready for it what kind of torq do i need for my surfaces. is the wing a plug in.
thx
Ben
[email protected]
hey chip when can we expect to see your vision 3d for sale i got a DA 50 all ready for it what kind of torq do i need for my surfaces. is the wing a plug in.
thx
Ben
[email protected]
#8
My Feedback: (8)
RE: Vision 3D release date
Not sure about the 1060 but the canisters fit very nicely underneath. I will get the measurements from DA and see what will work. I am leaving for Spain on Wed. and just returned tonight from a show in Antigua, so it may be next week before I can get back to you.
Chip
Chip
ORIGINAL: flyinrazrback
Chip, will the vision take a cannister only or is there enough room for a KS 1060 full pipe?
Chip, will the vision take a cannister only or is there enough room for a KS 1060 full pipe?
#11
Junior Member
Join Date: Oct 2004
Location: Segoviano, SPAIN
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
RE: Vision 3D release date
HI CHIP!!! I'm a spanish kid and I'll fly indoor on Saturday and Outdoor on Sunday.
See you in Madrid this weekend!!!!!
Luis Francisco Bernardos
http://www.acro3d.com team
See you in Madrid this weekend!!!!!
Luis Francisco Bernardos
http://www.acro3d.com team
#12
My Feedback: (8)
RE: Vision 3D release date
Luis,
I am sorry to say that your people on that end apparently never bought the tickets or something. I was supposed to recieve mine on thurs. but they never arrived. I have also spoke to the germans and they said the same. I was very dissappointed in the fact noone even called to explain, this info came from the Argentenians who were caught in the middle. I am sorry for not being there, but I didn't have any choice.
Chip
I am sorry to say that your people on that end apparently never bought the tickets or something. I was supposed to recieve mine on thurs. but they never arrived. I have also spoke to the germans and they said the same. I was very dissappointed in the fact noone even called to explain, this info came from the Argentenians who were caught in the middle. I am sorry for not being there, but I didn't have any choice.
Chip
ORIGINAL: Luispain
HI CHIP!!! I'm a spanish kid and I'll fly indoor on Saturday and Outdoor on Sunday.
See you in Madrid this weekend!!!!!
Luis Francisco Bernardos
http://www.acro3d.com team
HI CHIP!!! I'm a spanish kid and I'll fly indoor on Saturday and Outdoor on Sunday.
See you in Madrid this weekend!!!!!
Luis Francisco Bernardos
http://www.acro3d.com team