exicted about new TVPs
#26
Senior Member
Thread Starter
Join Date: Dec 2006
Location: IC, IA
Posts: 1,064
Likes: 0
Received 0 Likes
on
0 Posts
RE: exicted about new TVPs
ORIGINAL: osuwins
hey ravenlunatic, i was never able to get the sav.25 to wheelie, and the rollbar thanks,the back end was just to exposed, ive landed on the head before bent a fin and brook my engine block so im all about protecting my investment if there not,. thanks, oh yea im useing the same body but i have a proline ford 150 body im working on
hey ravenlunatic, i was never able to get the sav.25 to wheelie, and the rollbar thanks,the back end was just to exposed, ive landed on the head before bent a fin and brook my engine block so im all about protecting my investment if there not,. thanks, oh yea im useing the same body but i have a proline ford 150 body im working on
i hear ya on the protecting your investments. i too have bent a cooling fin. i think i'm going to use a larger body for the sake of a better fit. im thinking the lst, mgt size bodies would look better on the extended chasis, what do you think?
#27
Senior Member
Join Date: Jan 2006
Location: Columbus,
OH
Posts: 508
Likes: 0
Received 0 Likes
on
0 Posts
RE: exicted about new TVPs
good question ravenlunatic, i would take your truck with you and try it on for size, im not ready to buy a body yet, but i never thought about the opptions, i have an f150 im working on, its an osu theam, ive done some tweeking, added 30,000 weight to the diffs,got steel dogbones for the back for now , water proofed, i put the rx box on the side thanks to the idea from azzmanm his ride is nice, well this is what my ride finally looks like, ill run it tomorrow, and i can wait
#28
Senior Member
Join Date: Jan 2006
Location: Columbus,
OH
Posts: 508
Likes: 0
Received 0 Likes
on
0 Posts
RE: exicted about new TVPs
heres some pic. with the stock body, and blazer, i had to make some new holes but it works,my test run went great some carnege due to the fail safe glitch wile airborn, it applyed the breaks when i went off a jump at 15 feet in the air, it went end over end and landed upside down ass first on the right side[:@], damage is ---- right wheel hub where tie rod mounts brook, i just switched it out with the left one, rear rool bar cracked,header pipe bent, rear right shock mount screw bent, was able to fix everthing and finish bashing,, love this new mod
#30
Senior Member
Join Date: Oct 2007
Location: Amarillo,
TX
Posts: 1,099
Likes: 0
Received 0 Likes
on
0 Posts
RE: exicted about new TVPs
I dropped a set of RC Solutions X Lightning (black) TVP's on my old savage 25 (and the radio box and transmission case from an X) and love them to death....though.....they actually made my truck TALLER instead of dropping it down.....my new era roll cage wouldn't reach the mounting holes for the transmission so I put the stock roll bar on, and drilled a pair of holes through for the new era cage to mount to, and am using the gap between the roll bars to run my back pressure line with a steel coil cover over the fuel line.
made enough of a height difference that in order to mount the dodge body on the truck I had to use the taller rear body mount on the front (short one still fit fine in the back)
will post pics in a few once I get them pulled from the camera and uploaded.
made enough of a height difference that in order to mount the dodge body on the truck I had to use the taller rear body mount on the front (short one still fit fine in the back)
will post pics in a few once I get them pulled from the camera and uploaded.